Skip to main content
X-VENTISO home

Searches every page and every manual, submittal and spec sheet on the site. Try XV250 weight, gas interlock or BACnet.

Vibration Dampeners

Mechanical isolation for XV Series draft inducers

Isolates the draft inducer from the chimney, so vibration stays at the draft inducer instead of traveling down the structure.

XV Vibration Dampener with its five spring-and-bushing mount points.
Isolation
C-springs sized to each model
Control
Urethane motor mounts
Mounting
Between the flue adapters
Approach
Mechanical isolation, not a mat
Red urethane transmission mounts on a performance car drivetrain.

Mounted like an engine

Mounted Like a Performance Engine.

European carmakers don't bolt an engine to the chassis. They mount it on isolators tuned to that engine: firm enough to hold it in place under load, compliant enough to keep vibration out of the car.

XV Vibration Dampeners work the same way. Urethane motor mounts keep the draft inducer level and located while it runs. C-springs, sized to each XV model, do the isolating, so vibration stays at the draft inducer instead of traveling into the structure.

Two jobs, two parts: one holds the draft inducer steady, the other keeps its vibration out of the building.

Why it matters

Vibration Travels. Stop It Where It Starts.

A draft inducer sits on the chimney, and the chimney is connected to the building. Without isolation, motor vibration travels down the structure as structure-borne sound and shows up as hum in the rooms below.

The vibration dampener breaks that path at the draft inducer, where it starts. Structure-borne sound stops at the dampener instead of traveling into the flue system and the building.

Draft inducer on a chimney with a zoomed view of one of five isolation points: a stud through a urethane bushing, wrapped by a stainless C-spring, with a high-temperature rope gasket sealing the joint.
Open full size (image, opens in a new tab)

Construction

True Mechanical Isolation, Not a Fiber Mat.

  • Springs

    Sized C-Springs

    Do the isolating at five mount points, each a C-spring wrapped around a urethane bushing on one stud. Sized to the draft inducer they carry.

  • Mounts

    Urethane

    Keep the draft inducer level and located while it runs.

  • Seal

    Sealed at the Joint

    A ring rises to the draft inducer and seals the gap with a high-temperature rope gasket, like a wood stove door, so outside air can't get in and no draft is lost. Every connection between the draft inducer and the chimney runs through urethane or a spring.

  • Service

    Service-Safe

    A protective bracket sits under the draft inducer's hinge, so the springs are never crushed or stretched when the draft inducer is tilted open for cleaning.

  • Fit

    Direct Mount

    Mounts directly between the XV Series draft inducer and its flue adapter, or on top of a top-mount damper.

  • Isolates

    Structure-Borne Sound

    Stops vibration at the draft inducer before it reaches the flue system and the building.

A fiber mat under a draft inducer seals the joint but doesn't isolate vibration. The XV dampener does both. Upgrading to a neoprene mat doesn't fix it: those are made for commercial dryer vents, not fireplace chimneys. XV Vibration Dampeners are built for the draft inducer they carry.

Specifications

Vibration Dampener Specifications.

ModelFitsDimensionsMaterialWeight
XV-VBD-1250XV150 / XV25012-11/16" OD, 9-9/16" opening, 2" tall316L stainless5 lb
XV-VBD-350XV35016-5/8" OD, 13-3/8" opening, 2" tall316L stainless7 lb

Sold separately. One per draft inducer, matched to the XV model. Vertical installations only.

XV-VBD-1250 vibration dampener on a flue adapter, showing the rope-gasket seal ring, urethane mounts and C-springs.
XV-VBD-1250 on a flue adapter: seal ring with rope gasket, urethane mounts, C-springs.

Downloads

Documents and Drawings.

Bring us the project. We'll find the yes.